Adjustable type. The Standard size is the 124 series and the Adjustable size is the 125 series. Both types of C - Spanners have a satin chrome finish. Standard The standard spanner sizes enables an exact grip on the nut. Avoids shaft and nut damage. Safe and user-friendly. Adjustable The Adjustable Spanners allows for one spanner to be used on a
Learn More1Higher than standard nuts – prevents the spanner jamming on the nut. DIN 3110, ISO 10102 (metric sizes), Chrome Alloy Steel, chrome plated.
Learn MoreTo be more specific, there are approximately 18 different standard sizes for a spanner wrench. You might be surprised to learn the information that is provided in the list of spanner sizes below. Spanner Wrench Standard Sizes: MQ.6 or 5/32" (3.2mm) M2 or 3/16" (4mm) M2.5 or 1/4" (5mm) M3 or 5/16" (5mm) M3.5 or 11/32" (6mm) M4 or 3/8" (7mm)
Learn MoreProvide with appropriate surface protection for rust prevention. DOUBLE ENDED SPANNER SET (WITH RIB). CONTENTS. 6x7, 8x9, 10x11, 12x13, 14x15, 16x17.
Learn MoreGEDORE grinds the spanner jaws to the exact rated size, using a high-tech grinding machine. Perfect fi t is the most important requirement for non-damaging and safe work. Tolerances achieved by GEDORE Tolerances permitted by DIN standards 1. High-Quality Steel 31CrV3 Highly-effi cient eccentric presses cut the blank for an open-ended spanner from
Learn MoreFLANGE DATA CHART. Mactech, Inc. • 4079 Pepin Ave. Size. Flange Bolts. Raised. Face. Diameter. Bolt. Circle. Flange. Diameter. Quantity. Size.
Learn MoreDesignation Spanner design DIN 1810 Outer diameter lock nut mm mmin. HN 0 16–200.6–0.8, HN 1 Ø20–Ø22 20–220.8–0.9, HN 2-3 Ø25–Ø28 25–281.0–1.1, HN 4 Ø30–Ø32 30–321.2–1.3, HN 5-6 38–451.5–1.8, HN 7 Ø52–Ø55 52–552.0–2.2, HN 8-9 58–652.3–2.6, HN 10-11 Ø68–Ø75 68–752.7–3.0, Designation Spanner design DIN 1810 Outer diameter lock nut mm mmin.
Learn MoreThe third revision of the standard was taken up to bring it in line with IS 6131:1980 and IS 2027:1980 in 199 I. The ring wrenches (spanners) having non-preferred width across flats at both ends were deleted and many sizes which found prevalent use in the country were also included.
Learn MoreDesign: Inch sizes, short form. • Drive: ring end POWERDRIV® double-hex. • Standard: DIN 3113A /. ISO 3318/7738. • Material: chrome vanadium steel.
Learn MoreSlogging spanner 22 135 mm 1" AF 3" AF No. 133 shotblast fi nish 27 -130 mm - - No. 306 shotblast fi nish 22 - 135 mm 1" AF - 3" AF - No. 306 G shotblast fi nish 27 - 95 mm - - Deep
Learn More1978. 6 HARDNESS 6.1 The spanners shall be hardened over tbe entire length and the hardness measured at any point on the spanner shall be within the limits specified below: a) Up to and including 32 mm 39 to 44 HRC width across flats b) Over 32 mm width across 35 to 44 HRC flats
Learn More